s355nl steel thicknessOrigin: bbn STEEL
Thickness: 6mm to 350mm
Length: 200mm to 18000mm
Payment terms: L/C, T/T
Commitment: If we have no the size in stock, it takes about 20 days for us to produce the s355nl steel thickness for you if the quantity can be more than 10 tons.
Describe:Hot rolled steel strip with JIS standard SPHC - shenda-steel…Hot rolled steel strip with JIS standard SPHC,US $ 310 - 490 / Metric Ton, AISI, ASTM, BS, DIN, GBInquiry (Leave message and get the latest price)
s355nl steel thickness Equivalent
S355 European Standard Steel - joostdevree.nlS355 EN 10025 : 2004 Standard Structural Steel Plate. S355 structural steel plate is a high-strength low-alloy European standard structural steel covering four of the six "Parts" within the EN 10025 2004 standard. With minimum yield of 50,000 KSI, it meets requirements in chemistry and physical properties similar to ASTM A572 / 709.GAUGE TO THICKNESS CHART - Metaltrone Custom GAUGE TO THICKNESS CHART Gauge Stainless Galvanized Sheet Steel Aluminum Fraction inches (mm) inches (mm) inches (mm) inches (mm) 30 0.0125 (0.33) 0.0157 (0.40) 0.0120 (0.30) 0.0100 (0.25)Some results are removed in response to a notice of local law requirement. For more information, please see here.
Structural steel grade designations according to EN Structural steel grade designations according to EN-10025 & EN-10027 according to EN 10027-1: 2005, EN 10025-2: 2004, EN 10025-4: 2004 Steel group structural steel Mechanical characteristics XXX min. yield strength inMPa example EN 10025-2: S 355 J2 + Z35 + M , s355nl steel thickness The Number = minimum yield strength for smallest thickness.Material Properties of S355 Steel - An OverviewAug 23, 2015 · S355 is named based on it's minimum yield strength of 355 Mpa (N/mm2), However the yield strength reduces when you go up in thickness above 16 mm for flat products & hollow sections Here is the table showing reduction in yield strength based on thickness Up to 16 mm - 355 Mpa 16 mm < t 40 mm - 345 Mpa 40 mm < t 63 mm - 335 Mpa
The tensile strength of S355NL shall be 470-630 Mpa for the thickness equal and below 100millimeters,Above 100mm,the range shall be within 450-600 Mpa for structural steel plate S355NL. S355NL Low-Alloy High-Strength Steel PlateEN 10025 S355NL, CoswideClarkes of Stillington hold a stock from 15mm to 130mm thick and a plate size from 2000 x 1000 up to 12000 x 2000 depending upon thickness. With tailored sizes available from our forward ordered tonnage with EU based steel mills.Steel Ultrasonic Thickness Gauge - Grainger Industrial SupplySteel Ultrasonic Thickness Gauge. 6 products found. Shop Grainger for ultrasonic thickness gauges for nonelectrical measurements. Our thickness gauges can be used with virtually any nonelectrical material. Use it to measure the corrosion or erosion of plastic, rubber and metal by testing their thicknesses. Our ultrasonic thickness gages can be , s355nl steel thicknessSome results are removed in response to a notice of local law requirement. For more information, please see here.
NORSOK STANDARDTYPE OF MATERIAL: Structural Steel, PRODUCT STANDARD GRADE Hot finished tubulars seamless or welded prEN 10 225 Oct.00S355G1+N SCOPE This MDS specifies the selected options in the referred standard and modified requirements which shall supersede the corresponding requirements in the referred standard. The thickness is limited to 25 mm. QUALIFICATIONSCONSTRUCTION PLATESS355NL EN 10025-3 3.1 / 3.2 - EN 10204 / TCM Normalized Mechanical properties :-50° -40° -20° 0° +20° 16 20 27 34 40 16 20 27 34 40 16 20 27 34 40 16 20 27 34 40 16 20 27 34 40 16 20 27 34 40 Chemical composition : C Si P S Al N Cr Cu Mo Nb Ni Ti V max. max. max. max. min. max. max. max. max. max. max. max. max.
S355NL - Salzgitter AG 2,5*nominal thickness for bending axis parallel to rolling direction Chemical composition 1) (in percent by weight) at right angles to rolling direction unless min. max. C the product width is opposed to this.0,18% Si 0,50% Mn 0,90% 1,65% P 0,025% S 0,020% 2) N 0,015% Cu Notch impact energy0,55% Ni 0,50% V 0,12% Al 0,02% 3) CE 0,43% 4) S355NL